Save. Share. Connect.
Wednesday, May 25, 2016
VOLUME - NUMBER
NEPCON China,SMT/Hybrid Pkg,EDS,EWPTE '16
ATX/MDM West '16
productronica,The ASSEMBLY Show, IMAPS, MDM/Minneapolis '15
Nepcon South China '15
SEMICON West '15
ATX/MDM EAST '15
EDS, SMT/Hybrid Pkg,Wire Tech Expo '15
NEPCON China '15
ATX WEST/APEX '15
AATE and IPC MW 11
SMTAI, Autotest, ATX MW/MDM and Assembly '14
SEMICON West '13
Electronics West/MDM and IPC/APEX '13
SEMICON West '14
NEPCON China, SMT/Hybrid Pkg, EDS, NWPTE '14
IPC APEX '14
Electronics West/MDM 10
ATX Midwest, IMAPS, PCB West '13
ATX West '14
ATExpo & IPC MW 07
NEPCON China '13, EDS, more
SEMICON WEST/Intersolar '12
NEPCON China Product Preview '12
Atlantic Design/MDM 10
Electronics West/MDM 11
SEMICON WEST 10
Atlantic Design/MDM 11
ATLANTIC DESIGN & MFG '13
Atlantic Design/MDM 09
SEMICON WEST 08
NEPCON South China '13
ATExpo & IPC MW 08
Electronics West/MDM 08
NEPCON China Product Preview '13
Electronic West/MDM 09
SMTAI and productronica '13
Multi tradeshow Product Preview '12
AATE/IPC Midwest 10
Electronics West/MDM 12
ATE and IPC MW 09
SMTAI and productronica '13
Atlantic Design/MDM 08
HOME / CURRENT ISSUE
Add Message Board
Seika Intros New Production Machinery
Tandem fluxing and wavesoldering machines.
Torrance, CA — Seika Machinery, Inc. is introducing a new advanced Solder Paste Recycling Unit that enables approximately 90 percent of waste solder paste to be recovered as solder bar. The system provides major savings in disposal costs for factory waste, a reduction in CO
emissions, and reduced costs for solder bar — all by simply recycling waste. As an additional benefit, the recycling unit enables selection of manual mode and automatic mode using a touch screen panel.
The company is also showing its new Sawa Eco-Roll large-roll model that cleans wiper rolls up to 24-in. (610mm). The Sawa Eco-Roll eliminates waste and saves money by reusing wiper rolls for printing machines. In addition to providing a reduction in waste, use of the wiper roll cleaner results in reduced CO
emissions in just 20 minutes.
Wiper rolls are widely used for under-stencil cleaning to wipe off solder paste in the SMT printing process. Most of them are used only once, then are disposed of with other solder waste. Tests have shown that repeated cleaning of wiper rolls does not compromise their performance when cleaning stencil apertures.
Also new is the Sawa Ecobrid handheld and fully automatic low-VOC emission stencil cleaner. The cleaner provides up to a 66 percent reduction in CO
emissions, as well as a huge reduction in operating costs. In addition, the system cleans and dries in just five minutes.
The company is also introducing the Seitec Bravo STS-2533 IN H & SJ Soldering System, specially designed for in-line and modular selective soldering. The programmable system uses a special nozzle design and a spray fluxer unit, enabling high-quality soldering of leads and pads. Additional features include a conveyor with roller, a specially-designed solder pot and a drawer-type solder pot — making the two-unit system an excellent soldering solution for mass production.
Contact: Seika Machinery, Inc., 3528 Torrance Blvd., Suite 100, Torrance, CA 90503
310-540-7310 fax: 310-540-7930 E-mail: email@example.com Web:
See at APEX Booth #459.
© 2015 USTECH. All Rights Reserved. |
Contact Us: 610-783-6100 | firstname.lastname@example.org
powered by GIM