Save. Share. Connect.
Saturday, March 25, 2017
VOLUME - NUMBER
ADM Cleveland and APEC '17
ATX West and IPC APEX '17
SMTAI and IMAPS '16
SEMICON West '16
NEPCON China '15
ATX WEST/APEX '15
AATE and IPC MW 11
SMTAI, Autotest, ATX MW/MDM and Assembly '14
Electronics West/MDM and IPC/APEX '13
SEMICON West '14
IPC APEX '14
NEPCON China Product Preview '12
Electronics West/MDM 11
SEMICON WEST 10
Atlantic Design/MDM 11
ATLANTIC DESIGN & MFG '13
SEMICON WEST 08
Electronics West/MDM 08
NEPCON China Product Preview '13
Multi tradeshow Product Preview '12
Electronics West/MDM 12
ATE and IPC MW 09
NEPCON South China '16
Atlantic Design/ATX/MDM '16
NEPCON China,SMT/Hybrid Pkg,EDS,EWPTE '16
ATX/MDM West '16
productronica,The ASSEMBLY Show, IMAPS, MDM/Minneapolis '15
Nepcon South China '15
SEMICON West '15
ATX/MDM EAST '15
EDS, SMT/Hybrid Pkg,Wire Tech Expo '15
SEMICON West '13
NEPCON China, SMT/Hybrid Pkg, EDS, NWPTE '14
Electronics West/MDM 10
ATX Midwest, IMAPS, PCB West '13
ATX West '14
ATExpo & IPC MW 07
NEPCON China '13, EDS, more
SEMICON WEST/Intersolar '12
Atlantic Design/MDM 10
Atlantic Design/MDM 09
NEPCON South China '13
ATExpo & IPC MW 08
Electronic West/MDM 09
SMTAI and productronica '13
AATE/IPC Midwest 10
SMTAI and productronica '13
Atlantic Design/MDM 08
Add Message Board
ERSA Integrates Dispense Function into Printers
Dispensing feature integrated into the printer.
Wertheim, Germany — ERSA's VERSAPRINT printers now offer an easy-to-use and cost-effective option — a dispenser that adds single dots and lines dispensed after the printing process. The dispenser option an Archimedean screw for dispensing precision, and meets all of the prerequisites for it to be able to very accurately place the dots.
One or two dispenser units can be installed in the printer, so that two different media — either different pastes or paste and glue — are permanently available at the system, and they can be applied in one process step. The needle of the dispenser is automatically cleaned, the program cycle is totally programmable, assuring consistent, reproducible process parameters.
This new optional dispenser eliminates the need for a separate dispenser deployed to set glue dots or to add more solder paste to a board assembly — in the many cases where the printer alone could not handle all of the PCB's parameters. This has become a problem because of increasing miniaturization of products using stencils only 100 to 200µm thick.
At this thickness, and depending on the complexity of the assembly, the volume of paste that can be deposited is at the limit or even slightly beyond acceptable tolerances. One solution to this has been the use of costly step stencils, through which more paste can be deposited on individually determined positions. A paste dispenser provides a far more economical solution, but until now, a separate dispense system had to be used.
According to the company, programs for the dispensing process are user-friendly and easy to generate. The user sees an image of the layout on the monitor, and simply points to location that needs more paste; the media are set by zooming in and then marking the location.
This represents the maximum in user friendliness. Individual parameterizations of the dispensing sequence for each location, including its subsequent inspection, are a matter of course. With the dispensing feature integrated into the printer, the user is gaining additional value from the printer, while at the same time increasing equipment utilization.
Contact: ERSA NA, 1779 Pilgrim Rd., Plymouth, WI 53073
920-893-1779 E-mail: email@example.com Web:
See at APEX Booth #1825.
© 2015 USTECH. All Rights Reserved. |
Contact Us: 610-783-6100 | firstname.lastname@example.org
powered by GIM