Save. Share. Connect.
Tuesday, March 28, 2017
VOLUME - NUMBER
ADM Cleveland and APEC '17
ATX West and IPC APEX '17
SMTAI and IMAPS '16
SEMICON West '16
NEPCON China '15
ATX WEST/APEX '15
AATE and IPC MW 11
SMTAI, Autotest, ATX MW/MDM and Assembly '14
Electronics West/MDM and IPC/APEX '13
SEMICON West '14
IPC APEX '14
NEPCON China Product Preview '12
Electronics West/MDM 11
SEMICON WEST 10
Atlantic Design/MDM 11
ATLANTIC DESIGN & MFG '13
SEMICON WEST 08
Electronics West/MDM 08
NEPCON China Product Preview '13
Multi tradeshow Product Preview '12
Electronics West/MDM 12
ATE and IPC MW 09
NEPCON South China '16
Atlantic Design/ATX/MDM '16
NEPCON China,SMT/Hybrid Pkg,EDS,EWPTE '16
ATX/MDM West '16
productronica,The ASSEMBLY Show, IMAPS, MDM/Minneapolis '15
Nepcon South China '15
SEMICON West '15
ATX/MDM EAST '15
EDS, SMT/Hybrid Pkg,Wire Tech Expo '15
SEMICON West '13
NEPCON China, SMT/Hybrid Pkg, EDS, NWPTE '14
Electronics West/MDM 10
ATX Midwest, IMAPS, PCB West '13
ATX West '14
ATExpo & IPC MW 07
NEPCON China '13, EDS, more
SEMICON WEST/Intersolar '12
Atlantic Design/MDM 10
Atlantic Design/MDM 09
NEPCON South China '13
ATExpo & IPC MW 08
Electronic West/MDM 09
SMTAI and productronica '13
AATE/IPC Midwest 10
SMTAI and productronica '13
Atlantic Design/MDM 08
Add Message Board
Economical Wire Terminations from Zierick
Insulation-piercing crimp SMT terminal.
Mt.Kisco, NY — Zierick Manufacturing Corp. has introduced a new surface mount insulation piercing crimp terminal and the tools that quickly and easily terminate a wire to SMT PC boards. The new terminals reportedly reduce production costs, improve reliability, and enable faster processing speeds. This new method of termination combines the advantages of crimping, insulation piercing, and SMT. According to the company, this terminal creates a highly reliable and economical way to terminate wires. The system consists of a surface mount terminal and a terminating machine which feeds the wire into the connector and makes the termination.
While the new crimp terminal and the termination tools can be used whenever a wire needs to be permanently connected to an SMT board, their most popular utilization is for instances where the wire passes through the terminal and numerous serial connections are made to one single wire. A good example is channel block lettering, where a series of LEDs is attached to a pair of wires.
Compared to conventional methods, this new system is less expensive than a two-piece pin/socket connection or an IDC (insulation displacement connector) type of connection which provides strain relief. It is more cost-effective than soldering wires to a board by hand. By comparison, it also takes up very little area on the printed circuit board.
The terminal has a flat base and two sidewalls perpendicular to the base. Two insulation-piercing contact spikes protrude from the flat base. Between the contact spikes is a flat area to facilitate vacuum pick-up and terminal placement. There are two deep score lines near the transition area between the sidewall and the base of the terminal.
The new process begins with the terminal being placed on the SMT board together with the other required components. After the assembly goes through reflow, it is moved to the terminating machine which feeds the wire into the terminal and crimps the terminal walls over the wire. In the process, the insulation piercing spikes penetrate into the wire without the necessity of removing the insulation. The crimp not only facilitates the contact, but also provides excellent strain relief for the wire. The two score lines on the terminal wall ensure that no deformation is introduced near the edge of the solder fillets, thereby preventing cracking and peeling of the solder joint.
For more information, contact: Zierick Manufacturing Corp.,131 Radio Circle, Mount Kisco, NY 10549
800-882-8020 or 914-666-2911 fax: 914-666-0216 Web:
See at Productronica Booth #A4,141.
© 2015 USTECH. All Rights Reserved. |
Contact Us: 610-783-6100 | firstname.lastname@example.org
powered by GIM