Tuesday, September 27, 2016
VOLUME - NUMBER
Advertisements
Home/Current Issue >  Production > 

Common Causes of Adhesive Problems


High-tech adhesives are generally very reliable. When used correctly, they can resolve many design issues, saving money, time and effort. However, when issues do occur there are a variety of potential reasons for their failure. Common failures include no adhesion upon cure, reduced adhesive strength ...

Read More

Extended-Length LED Light Engines Speed Production and Cut Costs


Light engines up to 48 in. (122.91 cm) long and 15 in. (38.1 cm) wide are lighting up the bottom line of LED light fixture manufacturers that create products such as replacements for fluorescent lighting.

Read More

Risky PCBs: Factory Floor Tests: Part 3


This series is about floor level checks that can be performed by a process engineer when they do not have access to lab instruments or the time to send out samples to a qualified lab. In this installment, we will address solder mask liftage, de-lamination and contamination.
Read More

Inexpensive CAD Software, Expensive Design?


The last 30 years have borne witness incredible changes in the PCB, the backbone of any electronic product design. Package sizes that we thought were small and powerful are now are considered to be big and clunky. We have gone from big through-hole devices to chip scale leadless devices, even at times ...

Read More

Why Pay Twice? Getting the Most from Solder by Recycling


If you are part of an EMS company that uses wave soldering, you have already realized that only a small amount of the solder you purchase goes into your assembled device. The vast majority of the solder you purchase becomes solder dross. Most likely you sell it back to either your solder supplier ...

Read More

Am I at Risk to Use This PCB?


To properly test for issues with the through-hole process, it is important to understand how soldering occurs. The simplistic assumption is that machines, such as reflow ovens, wave soldering systems, selective soldering systems (or even people) create a solder joint. They do not. In all cases, these ...

Read More

Embedded Boards Offer New Solutions


Embedded boards ideally would lower costs while providing more functionality. Motherboards for the consumer market seem to fill this gap, unlike embedded boards, but they lack the longer lifecycles, the support and other features that industrial applications cannot do without. By providing semi-industrial ...

Read More

Selecting the Right High Tech Adhesive


Choosing the best adhesive can be a complex process. Carefully selecting the correct adhesive for a job will reduce the number of products that need to be evaluated and increase the likeliness of its success. There are many variables to consider and numerous types of chemistries with different capabilities ...

Read More

Improve Crimp Quality to Increase Productivity


High-quality crimp terminations will usually exceed the service life of a product in which they are installed. On the other hand, a marginal-quality crimp termination can cause electrical failures early in a product's life. Since a high percentage of product failures can be traced to poor electrical ...

Read More

Making Best Practices "All for One and One for All"


Your best and most experienced people on the manufacturing floor make an art of their work, but are sometimes reluctant to change. Your least experienced and/or most timid people avoid asking anything twice, so they wade through documention and search for answers.

Read More

Am I at Risk to Use This PCB?


There is only one way to answer this question, and that is with an examination by a qualified laboratory. However, production pressures, laboratory lead times and cost usually require some "less than definitive" answer. Even with access to a laboratory and control of the lead time, I sometimes find ...

Read More

Five Things to Know About Automatic Crimping Machines


Wire crimping is an important part of production lines that depends on the performance and reliability of a wire crimping machine. Such machines are available in a variety of configurations, as both manual and automatic systems. For larger production requirements, however, automatic wire crimping ...

Read More

Solutions for High-Mix Electronics Production


Hardware, software and process expertise for high-mix electronics production are special focus areas of ASM Assembly Systems. An SMT line solution that has been optimized especially for high-mix applications will use a DEK Horizon 03iX printer and two SIPLACE SX2 placement machines ...
Read More

Saline Lectronics' Lean Program


Earlier this year (February), early-stage plans were released to implement a new lean manufacturing program factory-wide at Saline Lectronics (www.lectronics.net). Upon attending the IPC APEX EXPO (www.ipc.org) in San Diego, CA, feedback from industry colleagues indicated surprise at an electronics ...

Read More

A New Paradigm in Crimping Press Design


It goes without saying that manufacturing companies want the highest possible quality at the lowest possible cost. These days, everyone is trying to do more with less in order to stay relevant in a highly competitive environment.

Read More

How High Is My Component? Tolerancing in Electronics


Tolerance in manufacturing refers to the amount of variation from product to product. It is often the observable difference between idealized computer models and tangible hardware. In surface-mount technology (SMT), such variations impact all aspects of the fabrication process, from component placement ...

Read More

What Every Contract Manufacturer Needs to Know About Product Development


In the landmark HBR article, "The Four Things a Service Business Must Get Right," by Frances X. Frei, the author differentiates a product business from a service business. The author states that in a service business, unlike products businesses, the customer is a key part of the product realization ...

Read More

Containers Cut Weight But Not Durability


Containers for storage or transport are often overlooked in the electronics industry, even though they can be critical to the function of any manufacturing facility or warehouse. Properly designed containers can provide protection and durability while at the same time trimming weight for increased ...

Read More

Handling Miniature Parts Safely With Vacuum Tweezers


Handling miniature parts is becoming more challenging for manufacturers since many parts continue to get smaller even as they increase their levels of integration and functional complexity. These miniature parts are being incorporated in a growing number of electronic products, including cellular ...
Read More

Case Study: Schleuniger Provides Automation and Quality for Draxlmaier Group


One thing all companies are continually looking to achieve is to cut costs and increase efficiencies. In addition, companies must remain compliant with the strict quality and safety standards of their industry, adding even more pressure. Because of this, innovative, automated and easy ...

Read More
 
 
search login